Recent content by riclourenco

Helllo, I installed RX Sound with the latest version of NASSP. Everything seems to be fine, but the sound of the engines during the launch of Saturn V has a very low volume on the exterior camera. Is there any way to adjust the sound volumes? Thanks

That's great! Thanks

So the alignment was really bad luck... If it weren't for that, right at the beginning when I managed to update the GET in the AGC, the rendevouz should have gone well after the take-off from the moon. So the only way to fix this would be to go back to the beginning of the PDI and land again I...

From what I remember, I did the P57 with the technique that is on the checklist. But of course I may have made a mistake that I didn't realize. I've done Apollo 11 several times for example, nothing like that ever happened, just like the previous Apollo 12. Regarding GET 130H between the two...

Thanks! I went back to GET 130H between the two EVAs where we do the "PRO, V37E 06E, PRO" procedure. The PROG light comes on after I do V37E06E. I think something is not right here either. Also regarding the clock being several hours out of date, I had already managed to correct it the first...

Hello, I have a problem with my Apollo 12 mission. This is the 2nd time I've done this mission, and I've been stuck for a week trying to figure out what I did wrong, taking into account that the first time I did the mission I didn't I had this problem, and everything went well. After the second...

Thank you very much. Next time after updating the NASSP, i will check these settings and correct them if necessary, before starting a new mission, to see if the same thing happens.

Hello, Thanks! yes I am using Orbiter2016 Beta+D3D9ClientBeta30.7-forBETA r90(r1436). I checked the settings and I just had to change the max. resolution level from 19 to 18, and the Mesh Resolution from 32 to 64. But unfortunately it didn't help. The last time I did Apollo 12, the terrain was...

Hello! I have a problem with the terrain I installed for Apollo 12 from the "Apollo Landing Sites for Orbiter 2016" website. On the landing site, there are places where the LM and/or astronauts are below the ground, and in others they are above. Here are some prints: Is there any way to...

Hello This problem of the crew dying after the splashdow also happened to me two missions ago on Apollo 11. In the following mission (the last one I did) after splashdow, the condition of the crew at a certain point was critical again. To prevent the crew from dying, as last time, I opened...

Thanks for the checklist, I did it well. I repeated as I said and the same thing happened. That is the problem. I added the crew at T-4h https://puu.sh/F0ecf/05dbf3e5b8.png Note that the CO2 partial pressure gauge is starting to rise soon. And note that is zero when we close the hatch in the...

Hello, thanks! I think I've figured out the problem. When I started the backup crew checklist at T-4h, I turned on project apollo MFD and selected ECS. I noticed that the number of crew members was zero. So I decided to add the three astronauts. It was the first time I did that. I just finished...

Hello, Today I was about to launch a new Apollo 11 mission. Before that I noticed that there was a new update for NASSP (1483). I upgraded before starting the mission. I started the checklist normally. However before reaching T-1h40m I noticed that the light of the CO2 press was on (yellow)...

Thanks Indy91 and MrFickles. I ill give it a try and go all the way to LOI-1, see how it goes :D.

Hello I am trying to do the apollo 12 mission, to see if I can at least reach the moon. So I decided to do apollo 11 too, to see if I can create the same Mission control PADs on Apollo RTTC MFD, so I could apply the same procedure on apollo 12. So I'm trying to do MCC1 on apollo 12,by trying...